大理石門套需要單獨做晶面處理嗎?
我們先來了解一下石材門套的一些細節:
Let's first take a look at some details of stone door jambs:
1、石材門套一般包含石材門套線條、內側平板、腳座這三部分組成;2、門套一般的高度是根據門洞來定的,不過一般都在2000mm以上;
1. Stone door jambs generally consist of three parts: stone door jamb lines, inner flat plates, and foot seats; 2. The general height of the door pocket is determined based on the door opening, but it is generally above 2000mm;
3、石材門套線和內側平板一般為壓蓋方式,也就是現場安裝時來組合而不是廠里組合加工好,會(huì )存在拼縫;
3. The stone door frame line and inner flat plate are generally covered by pressing, which means they are assembled during on-site installation rather than being processed in the factory, and there may be seams;
4、石材的板面不一定可以滿足單邊長度的要求,所以在垂直方向和水平方向就需要分斷,這就會(huì )增加現場安裝的拼縫;
4. The board surface of the stone may not necessarily meet the requirements of single side length, so it needs to be broken in the vertical and horizontal directions, which will increase the number of joints installed on site;
5、門套線在轉角位置會(huì )碰角,這個位置也會(huì )增加拼縫;
5. The door pocket line will collide at the corner position, and this position will also increase the seam;
6、石材在運輸和安裝過程中會(huì )不可避免地出現斷裂和缺角的問題出現;
6. During transportation and installation, stone materials will inevitably experience fractures and missing corners;
7、石材本身亮度和在廠里加工中打磨不夠時的加工位置的亮度不足。
7. The brightness of the stone itself and the brightness of the processing position when it is not polished enough in the factory are insufficient.
石材門套線與側板壓蓋縫隙
Gap between stone door pocket line and side plate cover
在了解了石材門套的一些細節之后,就會(huì )知道石材安裝完成之后會(huì )有比較多的問題,使得其達不到較好的裝飾效果,這就需要來做晶面處理。石材門套線的拼縫,接縫,斷裂,缺角,磨損等的問題都可以通過鏡面處理來。而一般的石材安裝師傅只會(huì )簡單地打磨,而不能很細致地去做晶面處理,所以就需要的石材晶面打磨師傅來做晶面處理。
After understanding some details of the stone door jamb, you will know that there will be many problems after the installation of the stone, which makes it unable to achieve a good decorative effect. Therefore, it is necessary to perform crystal surface treatment. The problems of stitching, seams, fractures, missing corners, and wear on the stone door cover line can be solved through mirror treatment. However, ordinary stone installers only perform simple polishing and cannot perform crystal surface treatment very meticulously, so professional stone crystal surface polishing masters are needed to perform crystal surface treatment.
石材門套晶面處理的效果:
The effect of crystal surface treatment on stone door jambs:
1、拼縫,接縫位置重新調膠打磨,使得縫隙位置和其他部分一致且亮度一致;
1. Splicing, re glue and polish the seam position to ensure that the seam position is consistent with other parts and the brightness is consistent;
2、石材斷裂和缺角位置修補完整且一致;
2. Complete and consistent repair of stone fractures and missing corners;
3、所有縫隙處理完成。
3. All gaps have been processed.
因此石材門套在安裝完成之后都需要單獨做晶面處理,這可以很好地保證石材門套安裝完成的實際效果。
Therefore, after the installation of the stone door jamb, it is necessary to perform a separate crystal surface treatment, which can effectively ensure the actual effect of the installation of the stone door jamb.