不銹鋼門套線包邊施工步驟有哪些?
1.用沖擊電鉆在門四周大洞眼,并插入木楔。
1. Use an impact drill to drill large holes around the door and insert wooden wedges.
2.將15厘大芯板(或夾板)靠墻側進行防潮處理(刷光油2遍后在貼珍珠棉)。用釘槍校正固定后,再用鐵釘加固。門套線條打底用9厘夾板。打底夾板外側用實木線條收口。合頁位置加板襯固或封兩層15厘大芯板。
2. Moistureproof treatment shall be carried out on the 15 cm large core board (or plywood) against the wall side (apply pearl cotton after two coats of varnish). After correction and fixation with nail gun, use iron nails for reinforcement. 9 cm plywood is used for the bottom of door pocket line. The outer side of the backing plywood is closed with solid wood lines. The hinge position shall be lined with plate or sealed with two layers of 15 cm large core plate.
3.門套與門扇相合之處到進門邊的側面用9厘夾板做止口板,止口深度與門的厚度相同。
3. From the joint of the door pocket and the door leaf to the side of the entrance door, use a 9 cm plywood as the seam plate, and the seam depth is the same as the thickness of the door.
4.面板用白乳膠涂勻后貼于打第大芯板及止口板上,并用不銹鋼蚊釘適當加固。
4. The panel shall be evenly coated with white latex and then pasted on the second core plate and mouth plate, and properly reinforced with stainless steel mosquito nails.
5.門套線條寬度一般為60mm—80mm.厚度8mm.
5. The width of the door pocket line is generally 60mm-80mm, and the thickness is 8mm
6.廚衛門套線條里側用不銹鋼(啞光)線條為宜。
6. It is advisable to use stainless steel (matt) lines on the inner side of the kitchen and bathroom door pocket lines.
7.門套及門窗套垂直、水平誤差不超過2mm(2m以上不超過3mm)對角線誤差不超過3mm(2m以上不超過5mm).
7. The vertical and horizontal error of door jambs and door and window jambs shall not exceed 2mm (more than 2m and not more than 3mm) and the diagonal error shall not exceed 3mm (more than 2m and not more than 5mm)
8.門套兩側墻與門套之間距離在門套線條不能壓住接縫時,宜先用水泥砂漿掛鋼釘封平(用板定模灌漿)干燥后方可封板打第,在門套線條能壓住接縫時可用板封龍骨結構。
8. When the distance between the walls on both sides of the door jamb and the door jamb is that the door jamb line can not press the joint, it is advisable to use cement mortar to hang steel nails to seal it (use plate fixed mold grouting) and dry it before sealing the plate. When the door jamb line can press the joint, the plate can be used to seal the keel structure.
9.單面門套用9厘板打底(凸窗應注意窗簾位置)。其他與雙面門套同。入戶大門可封單邊實木線條門套。
9. Single-sided door jamb is bottomed with 9 cm plate (pay attention to the position of curtain for convex window). Others are the same as double-sided door jambs. The entrance door can be sealed with single-sided solid wood line door pocket.
10.窗套不宜包臺面,臺面用大理石鋪貼(防盜網宜在窗套面板封后制作)。單面門套:在原來有門的基礎上起裝飾作用,不起承受門的力量。
10. The window cover should not cover the table top, and the table top should be paved with marble (the anti-theft net should be made after the window cover panel is sealed). Single-sided door jamb: It is used for decoration on the basis of the original door, and cannot bear the power of the door.